HOW TO REMOVE AND ALSO CHANGE A BATHTUB

How to Remove and Also Change a Bathtub

How to Remove and Also Change a Bathtub

Blog Article

Top Article

This great article down below involving How to Install a Bathtub Yourself is indeed entertaining. Check it out for yourself and decide what you think of it.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a bath tub isn't exactly brain surgery, yet it does require strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is readily available, the task can move rapidly; if you need to open a wall surface to get rid of the old tub as well as place the new bath tub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need a helper to vacate the old bathtub and set in the brand-new one. Ensure you have actually certified yourself for the work and fit attempting it. As opposed to employing a professional to take control of a halfway-completed project, it is far better to think about using one before you start. Chances are you may require a professional plumber to make tube connections.
This article will aid you set up a brand-new bathtub in your washroom if you have currently bought a new bathtub and don't need to transform the plan of your previous water pipes.
Your devices as well as material list need to make up the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Setup


    Firstly, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to stop stress on the bath tub.
    Fit the adaptable tap connectors to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its final position.

    Removing Old Taps


    If you require to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, turn on the taps to drain any water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome as a result of the limited accessibility that is often the case.
    Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
    Prior to carrying on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.

    Mounting the Tub


    Utilizing the two wooden boards under its feet, position the tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
    The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bath tub till the spirit level checks out level.
    To mount faucets, fit all-time low of the furthest flexible tap adapter to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
    Switch on the water supply and examine all joints and also brand-new pipework for leaks and tighten them if essential. Load the tub and additionally inspect the overflow outlet and also the typical outlet for leaks.
    Lastly, repair the bath paneling as described in the maker's instruction manual. Tiling and securing around the tub should wait till the bathtub has actually been utilized at least when as this will settle it right into its final position.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipelines.
    If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the tap as well as the sink. Secure the tap in position with the manufacturer supplied backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet ports. The previous type must be attached to the tap finishes initially, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.

    Tiling Around the Tub


    In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, creating the water to pass through the wall between the bath as well as the tiling, resulting in problems with moisture and also possible leaks to the ceiling below.
    You can choose from a variety of coloured sealants to assimilate your components as well as installations. They are marketed in tubes and also cartridges, as well as can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to allow for the movement experienced when the bathtub remains in use. The sealant can break relatively early if you do not think about this activity prior to securing.
    Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof sticky as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    Do you enjoy more info about A Step-by-Step Guide to Installing a Bathtub? Leave a remark directly below. We will be interested to hear your ideas about this content. Hoping that you visit us again before long. Do you know anybody else who is fascinated about A Step-by-Step Guide to Installing a Bathtub? Please feel free to share it. I value reading our article about How to Install a Bathtub Yourself.




    Browse Website


    Report this page